好的軍事模型制作完成后逼真，可供人觀賞，也可用于軍事教學。那么大型軍事模型的制作有什么步驟呢？有工具的可以一起來做喲！

　　Good military models are lifelike and can be used for people's enjoyment and military teaching. So what are the steps involved in making a large military model? Those who have the tools can do it together!

　　工具

　　tool

　　模型一套、模型膠水（田宮和小號手ABS膠水）、筆刀、水口剪鉗、直彎鑷子兩支、九洋切割板、打磨條、砂紙一套銼刀一套、模型手鋸、模型手鉆（鉆頭有0.022mm的鉆頭）、模型開模器、打磨塊、牙膏補土、模型AB補土、水補土。如果模型設計不合理想要改進或者增加金屬細節我們可以用到PE（銅制蝕刻片）ABS塑料膠板、銅線。上色工具有面相筆、平頭畫筆和噴筆噴泵、遮蓋帶。舊化裝備有舊化土、漬洗液，也可用丙烯顏料加打火機油做漬洗。

　　Model a, model glue (tamiya and trumpeter ABS glue), pen knife, shuikou pliers, straight curved tweezers two, article 9 the cutting board, grinding, abrasive paper, a set of file a model, model handsaw, hand drill (0.02 to 2 mm drill bit has), model open mode, putty grinding block, toothpaste, water model AB putty, putty. If the model design is not ideal to improve or increase the metal details we can use PE (copper etching sheet) ABS plastic plate, copper wire. Coloring tools are face pen, flat brush and spray pen spray pump, cover belt. Old equipment has old soil, stain lotion, can also be used propylene pigment and lighter oil to do stain washing.

　　方法

　　methods

　　我們說組裝，按照說明書的編號指示，找到相應編號的零件板件，按照英文字母的數字編號，使用水口剪鉗剪下零件將水口用筆刀削整，砂紙打磨平整后，涂上模型膠水，與另一個零件相粘，并用手壓緊十秒鐘左右就可以了，兩個零件之間對合留一條小縫，用綠蓋膠水刷上一點即可膠水順著縫隙流滿后用手壓緊使膠水溢出，待完全干后用砂紙打磨平整即可，此方法不是一次就行需要多次點膠，如果零件契合不好溜縫膠水無法彌補住縫隙時我們就要用到牙膏補土了，將牙膏補土擠出涂在縫隙上，使用一次性探牙針或筆刀進行填縫，待干后使用砂紙打磨平整即可。

　　First we say assembly, the number of instructions, in accordance with the specification to find the corresponding number of parts, the panel is according to the number of English letters number, use the shuikou pliers to shuikou pen knife cut the whole cut parts, sand paper after grinding smooth, glue coating model, and the other parts are glued, pressure for more than ten seconds with the hand, involution leave a small crack between the two parts, With green cover brush a little glue can glue along the gap flow pressure make the glue overflow with the hand, after the expiration of the stay dry sanding formation can be used after completely, this method is not just a need glue for many times, if the bad parts fit slip joint glue cannot make up for live gap when we're going to use toothpaste putty, putty squeeze toothpaste besmear is on gap, Use disposable probing needle or pen knife to fill the gap, and use sandpaper to smooth it after drying.

　　上色

　　coloring

　　上色是模型三步走的（組裝上色舊化）第二步，我們要知道，上色是手繪還是噴泵噴涂，無論手繪還是噴涂在上色之前都需打上一遍水補土，水補土可以視為底漆，也可視為模型更后的補縫劑，上色時也可以似的模型漆的附著能力更好，也可以判斷模型的迷彩涂裝是否均勻，使用之前上下?lián)u晃均勻。

　　Color is the model of the three steps of paint (assembly) old second step, the first thing we want to know, color is hand-drawn or spray pump spray, hand-drawn or spray before coloring are required to play in the water again fill soil, water putty can be regarded as primer, model also can be regarded as the final fill seam an agent, color also can model paint adhesion ability is better, You can also judge whether the camouflage coating of the model is even. Shake it up and down before using it.

　　上色后注意事項

　　Note after coloring

　　手鉆是為模型定位孔打孔用的，很多老式模型零件定位孔，沒有全部打開，需要玩家自己開孔，這時我們就用到了手鉆，手鉆在改造塑料履帶可動方面也是要用的。使用筆刀修整零件時一定要注意防止割傷自己或刀片崩裂造成傷害。模型制作一般不適用14歲以下人群，適合成人或14歲以上玩家。模型不是玩具不適合把玩。

　　The hand drill is used to drill the positioning holes of the model. Many positioning holes of the old model parts are not all opened, and the player needs to open them by himself. At this time, we use the hand drill. When using a pen knife to repair parts, pay attention to safety to avoid cutting yourself or blade breakage. Model making is generally not suitable for people under 14 years old, suitable for adults or players over 14 years old. Models are not toys to play with.

　　市場上的模型五花八門，所以在選擇上需要多加注意才是，更多內容就來我們網站看看吧！

　　The model brand on the market is multifarious, so on the choice needs to pay more attention to is, more content will come to our website to see!